Safety and Testing Questions: Q: Has the NecksGen REV passed any safety standard testing? 00+ GST (Prices are subject to change without notice). A: No, the NecksGen unit comes with all the helmet hardware needed. Q: What should the gap between my upper belts behind the seat be?
Q: Does the NecksGen REV offer any side protection? A: The NecksGen REV has upper belt guides that will keep a secure belt on at all times. If you have a new SAH2010-2015, or SA2020 + helmet, or a pre-drilled helmet, simply use these pre-determined and drilled locations to mount your helmet hardware. Winglets - Large adult units can accept 2" or 3" seat belts. In the event of an accident, the unit is held back by the seat belts, whereas the body, neck & head will move forward and away from the device. The NecksGen REV 2 LITE is the ultimate head and neck restraint. It works great with my pyrotect helmet and is a super versatile system. However, the NecksGen Small can only accept 2" belts.
A $30 restocking fee will be charged. A: Yes, the NecksGen REV has self aligning tethers that offer range of motion from left to right. Free re-certifications on the REV2 Lite will be honored for SFI 38. If it is not 2 inches, contact NecksGen for an appropriate length tether for your situation. 0 inches of total slack. Note that 3 point harnesses are not compatible. Quick release helmet hardware. NecksGen Part Number: NG501 NecksGen REV2 Lite - Medium 3″. Tension Neutralizing Tether - Using a proprietary single tension-neutralizing tether (TNT), the loads under impact are distributed through four different load paths. Combining the safety of an SFI 38. Just put your belts on and go. Simple instructions are included with your device. The recertification costs will vary by device and it's needs, but typically it costs $114 average.
Note that the SFI label cannot be removed or altered, so if you paint your device you will need to have it recertified after painting. A: The NecksGen REV is made from a Dupont carbon fiber composite. The entire package includes quick release helmet hardware, tool kit, and bonus decals. Please refer to the Tether Length page to learn how to do a tether slack test to check that the tether is the correct length for you. This light head and neck restraint is constructed with composite material, weighing only 1. ALL New REV2 Lite head and neck restraint. The medium unit fits most adults however your neck width will determine which size you need. Please be sure to follow all instructions in manual and installation guide on reassembly. Q: Will the NecksGen unit interfere with my roll bar/cage?
A: Yes, included in the price for $599 you get Quick Release helmet hardware. Every time we pull one of these out of the box, thing is light! Emergency Pull - pictured separately. You must login to post a review. If you want more, please email a request to: Carry bags can be purchased from the accessories tab. Works with 3″ shoulder harnesses and fits drivers with necks wider than 6″ comfortably. A: No, the NecksGen REV uses standard tools. Do not purchase a tether that will allow more than 3″ of slack.
1 approved, Very small, 550 grams, sits low on your body well away from your helmet, has state of the art easy to use quick release helmet hardware and of course side impact protection. Slack Test: Get buckled in your car as if you are ready to race and look straight ahead to the horizon. The NecksGen REV 2 LITE model takes comfort, fitment and helmet clearance to a new level. 1 certified device, with the comfort of the small package of the REV, it's just a matter of choosing which size works best for you. After a crash, the effectiveness of the NecksGen unit can be greatly diminished if there is any damage to the device. Absolutely love the NecksGen. Parts not included in re-certification: tether, shoulder pads, friction pads, hardware, etc. The NecksGen units are designed and made in the USA, using the latest carbon fiber composite Dupont material. Today we're proud to provide quality products direct to your doorstep through an experience you'll enjoy. The belt channels accommodate 3 inch harnesses and have friction pads and high outer belt guides to help keep your shoulder harnesses in place while driving and even in the event of multiple impacts.
If you are on the edge between a medium and a large but have narrow shoulders, go with the medium. Fits necks up to 6" wide. If you have a REV, tethers are available in one inch increments. The REV2 Carbon is new for 2020, and is currently the lightest head and neck restraint available. Tethers do not expire, but we recommend replacing them any time there has been a significant crash, you can see any sign of damage, or every 2 years. Click HERE for NecksGen frequently asked questions! Please see features page for more info. This proprietary design allows for maximum range of head motion with superior frontal and side impact protection. Which fits up to 6" wide necks. Frequently Asked Questions. A: Yes, the NecksGen REV incorporates lateral tethers, that offer alternative load paths in side-on impact for superior protection.
Please introduce yourself to start live chat. This unique system offers an equal distribution of forces under impact. Tether Questions: Q: Do I need to adjust my tethers? A: Yes, the NecksGen REV unit will work with most race seats without any modifications. NecksGen is the leader in head and neck restraint safety. Devices manufactured after 2021 will not have a date sewn into the tethers in order to not cause the confusion over the dates. With simplicity and ergonomics leading the design flow, the REV 2 LITE design has no need for a frontal yoke. The wings aid in keeping your harness in place under impact.
By filling out your request we can better decide what level of sponsorship we can provide for your type of racing based on the current year's plan. We do supply a tool kit. Available in Medium, or Large. Features the new integrated adjustable tether design, sizing and fitment are easier than ever. The simple, easy to use design carries over from the popular REV2 Lite, and has the same level of certification and safety as all NecksGen head and neck restraints. For multiple impact situations higher belt guides help keep everything locked in place, and the shoulder pads are improved. Q: Is the Quick Release hardware easy to use? If there are no holes in your helmet, you may need to drill the 2 holes to mount your hardware. Call or email us today to let us know what you think. The brand new REV2 Lite for 3" shoulder harnesses has advanced features that elevate it to new found levels of comfort. In addition to the features above, the REV2 Lite adds a new adjustable tether system, rubber grip pads, and higher belt guides to keep everything locked in place during multiple impact situations. Please be sure that both shoulder harnesses wrap around the shoulder and extend behind the seat at a -10 degree angle.
keepcovidfree.net, 2024