Step 3: Go Shopping. Many dealers don't update their units that are previously mounted or sitting on a shelf waiting to be sold. If you are unsure, you might want to check your user's manual for directions. Use rubber washers between the console's fiberglass and the mount to reduce rattling and prevent the console from getting scratched by the bracket. Put rubber washers between the fiberglass and the mount. Fish finding systems have two components: the transducer and the display. Mounting a transducer on a pontoon boat. It is also possible to add a small battery next to your fish finder, completely separate from your other boat's electrical components. Fortunately, there's a better install method that won't require you to run a wire clear back to the battery, and will give added protection. "I want to install a fish finder on my pontoon boat, but my eyesight is bad. It's a good idea here to use rubber washers between the console's fiberglass and mount. Adding a depth finder is something that can and a measure of safety to the boating experience. This is an excellent location for the installation of the transducer.
The nice thing about using a transducer mounting pole is that you can point your transducer in different directions independently of the trolling motor, simply by rotating the handle of the mounting pole. If your pontoon boat does not have a mounting bracket for the transducer, use an aftermarket transducer bracket. Transducers are not all the same. Mounting a transducer on a pontoon boat top. My buddy has that exact fish finder and his is mounted on the left toon and works great. We also had to drill another hole in the deck under the console. Drill a hole in the boat's hull. The best fish finder for shallow waters. Mark the sections where you must drill holes for the mounting screws. Rubber grommet for cords to go through the console (optional).
So the ideal transducer mounting height on the transom is with the bottom surface of the transducer just slightly protruding below the bottom of the boat (see diagram above). What you will need to do is adjust it so that it's parallel to water when sitting in water. The best place to install the fish finder's transducer is usually on the starboard (right) side of the pontoon boat. Wonder why bennington put it on the port side? Drilled two holes in the aluminum bracket and used the Humminbird mount. Since pontoon boats are built on top of pontoon tubes, they don't have a transom like other boat types, and so require a different using a different location to mount a transducer. Six nuts that fit on the six bolts above. However, instead of drilling a hole on the boat's outside surface, you will have to do it inside the hull. Then simply connect the bracket with nuts and bolts on the console. This will help you put them back easier. Mounting transducer on bennington pontoon boat. 6mm) drill bit and drilled through the bracket in two spots. Many retailers don't sell the transducer together with the fish finder, so please get the transducer as well. Transducer mounting bracket. This is where you'll run your cables.
Check the package that you bought to make sure you have one. Get a 1/4" drill bit and drill two holes through the bracket. Transom transducers connect to the transom instead of the hull.
Once you've determined where your monitor will be placed, check under the console to ensure none of the other wires will get in the way. It sounds like the beach doesn't have much of a slope. You may find that the cord going from the transducer up to the monitor only has enough length to run off one of the pontoons. The fish finder comes with pretty much everything you need to mount it on a traditional boat, but not nearly all you need for a pontoon. How to Install a Fish finder on a Pontoon Boat. Select a Fish Finder Suitable for Your Situation. Put everything back together. Then the other battery will be for engine starting only. All in all, you'll only need an hour or so to complete all the steps necessary. My pontoon has the usual mounting bracket on the end of the keep the transducer from being torn off I was hoping to mount it inside the bracket using epoxy. Once you have a clear path to place the wire inside the siding, put the plastic conduit shroud around the transducer wire and fish it through all the way up to the console. By putting it onto a different power source and wiring it separately on the fuse panel you will probably see different results.
Pro Tip: Ensure the hole forms a 90-degree angle with the waterline. You want the transducer with approximately the bottom one quarter an inch in the water when on plane. If I wire or re-wire any accessories I try to use separate circuits from the battery switch unless I have open circuits in the fuse block. Set the wires to run through your boat and into your fishfinder console. Image credit unknown, found shared on Facebook. When mounting the fishfinder, set the bracket in place and place it wherever you wish to. Went to Amazon and ordered another transducer. Its signal range is horizontal and it has a beam that you can adjust mechanically. Most boats will have the space to fit one, sometimes to the side of the actual instrumentation. Insert the transducer in and secure it with a bolt and nut. These transducers are mounted on the inside of the hull's bottom. Transducer placement. For single-drive watercraft, it would be best to position the transducer away from the propeller's path.
Steps to Mount a Transducer on a Fiberglass Boat. This part can be tricky.
keepcovidfree.net, 2024