Turn the engine off and remove the ignition key. Craftsman lawn tractor belt diagram. Take note of the belt configuration and remove the old belt from all drive and idler pulleys. Reinstall the two outer mandrel covers and tighten the screws securely. Replacing the deck belt on your Craftsman lawn mower is a relatively easy operation once the mower deck is removed from the lawn tractor. Go to the other side of the mower and disengage the left front suspension arm and left rear lift arm the same way.
Disconnect the front link between the deck and the mower chassis by removing the retainer spring and washer from the pin on the chassis and pulling the front of the link from the pin. During normal mowing operations on an established lawn, the deck belt on your Craftsman FS5500 riding mower usually lasts for two or three mowing seasons. Slip the belt off the pulley by hand. Go to the left side and push the belt tension rod down and then secure it by hooking it into the slot in the lock bracket. Unwind the remainder of the old belt off the idler pulley, located on top of the mower deck near the rear of it. Craftsman 50 inch riding mower belt diagram. Grasp the forward-facing belt tension rod on the upper left of the mower deck. Check the entire belt for proper routing and alignment in all the pulley grooves.
Maintain a firm grip, lever downward and push the end toward the tractor to disengage the spring-loaded rod from the slot in the lock bracket. If you forgot to take a picture of your mower's deck belt before removing it, refer to your mower's owner manual for the correct routing pattern. If necessary, refer to the photo you took after removing the mower deck from the lawn tractor. Wiggle the belt between the pulley and the guide to remove it. Consequently, periodic belt checks are called for -- and when it becomes necessary, replacing the belt takes less than an hour. When working on your lawn mower, always engage the brake to prevent rollaway, turn off the engine and remove the key to prevent injury. Slide the mower deck out from under the right side of the tractor. But when mowing through unfinished areas, friction caused by flying dust, gravel and debris causes abnormal belt wear. Remove the screws securing both mandrel covers to the left and right of the deck using a Phillips screwdriver. Craftsman riding mower drive belt diagram. Remove the belt from the second mandrel pulley by using your hands to slip it up between the large belt guide (a half-dome shape) and the pulley.
Williams is a winner of Writer's Digest Magazine's annual writing competition. Install the belt around the three mandrel pulleys with the "V" of the belt facing inward toward the pulley groves. Turn the tractor steering wheel so that the wheels point all the way towards the left. Remove all dirt and grass clippings from around the pulleys and the upper deck surface with a stiff-bristle brush. Kelly then established an organization specializing in home improvement, including repair and maintenance of household appliances, garden equipment and lawn mowers. After graduating from the University of the Witwatersrand and qualifying as an aircraft engineer, Ian Kelly joined a Kitchen remodeling company and qualified as a Certified Kitchen Designer (CKD). Slide the deck under the tractor and center it front to back and side to side. Remove the retainer spring and washer by hand from the pin protruding through the hole in the front right suspension arm located on the upper front of the deck, and then disengage the link.
Then you only need your two hands to remove the old belt and install the new one. Remove the old belt from the mandrel pulley located on top of the mower deck near where the cut grass discharges. This pulley may have a small belt guide that looks like a narrow piece of metal sticking up beside the pulley. How to Put a Belt on a Craftsman FS5500 Riding Lawn Mower. Slide the loose front section of the new belt over the electric clutch pulley.
Ensure the belt is completely in the pulley grooves. Reinstall the front right suspension arm by sliding the slot on the end over the pin protruding from the chassis and replacing the washer and retainer spring removed earlier. It only becomes a challenge when you don't know the correct pattern for routing it around the pulleys on the mower deck. Set the parking brake, place the clutch lever in the "Disengaged" position and lower the attachment lift lever to its lowest position. Loop the flat side of the belt over the two idler pulleys and feed the loose end of the belt forward towards the clutch pulley position.
keepcovidfree.net, 2024