Inspect bin gasket prior to ice machine installation. Navigation with the touchscreen provides access to menu items, machine information, settings and event logs. D. Leak-check line set connections, S trap and all factory joints in head section and condensing unit. Above stainless steel. It'll get stuck in off mode. Indigo nxt ice machine not making ice. Select Exit to return to previous screens and. Part Number 000014141 Rev 08 5/21 39 Operation Section 3 Safe Operation Mode Allows the ice machine to operate up to 72 hours if the ice thickness probe and/or water level probe sensors fail. CHECK VALVE CONNECT MANIFOLD GAUGE SET OR HOSE WITH CORE DEPRESSORS ON BOTH ENDS LINE SET CONNECTION LOCATION CONDENSER CONNECT VACUUM PUMP TO SHUTOFF VALVES FOR THE LINE SET Part Number 000014141 Rev 08 5/21 29 Installation Step 4 Open Valves for the Line Set and Receiver. Insulation Thickness Suction Line 1/2" (13 mm) Liquid Line 1/4" (7 mm) Suction Line 3/4" (19 mm) Liquid Line 1/4" (7 mm) Step 7 Insulation for the Suction Shutoff Valve. Low ambient air temperature under 50 degrees Fahrenheit isn't suitable for the ice maker either. There are a number of buttons that do different things, including power and clean, besides just navigation.
Fill spray bottle with sanitizer and spray all interior food zone surfaces. Indigo nxt ice machine how to turn on touch. With its touchscreen display, this unit can be programmed to turn off at certain times of the day or to produce a specific volume of ice. All minimum responsibility. Part Number 000014141 Rev 08 5/21 45 Maintenance Section 4 Step 11 Use half of the sanitizer/water solution to sanitize all food zone surfaces of the ice machine and bin (or dispenser). Water curtain off or stuck Water curtain must be open.
Power the machine off from behind. Detects if Ice Level Sensor, Accessory LuminIce II or AuCS are Detection connected. Easy to clean food zone with antimicrobial components. Innovative clear-coat resists fingerprints. Out of the On/Off Mode and the Power button will. Pressure test the line sets and CVD Condensing Unit with 150 psi (1000 kPa) of dry nitrogen. · Insulate water and drain lines to prevent condensation. 5 to 7 minutes - The water dump valve energizes. 48 Part Number 000014141 Rev 08 5/21 Section 4 Maintenance Cleaning the Air Filter and Condenser The washable filter on self-contained ice machines is designed to catch dust, dirt, lint and grease. If water flow isn't working, then water lines to Manitowoc are clogged. Indigo Control Board Navigation –. N otice Indicates information considered important, but not hazard-related (e. g. messages relating to property damage). Ground Fault Circuit Interrupter We do not recommend the use of a GFCI/ GFI circuit protection with our equipment. If a greasy residue persists, use a damp cloth rinsed in a mild dish soap and water solution.
Measured Rise (R) 35 feet (10. Summary of Menu Options. Turn off the ice machine, if water continues to enter water trough, replace the water inlet valve. Please contact us if you want to verify or to discuss other options that may be available sooner. 5 lbs - 680 g IF0600N JCF0900 1. Manitowoc ice machine panel off. How do I turn to on? - Archives. The ice thickness probe can be descaled and sanitized at this point without complete removal. Holes are provided on the corners of the condensing unit to allow the use of lifting shackles.
Do not allow children to play with, clean or maintain this appliance without proper supervision. 8 380-460/3/50-60 - - - - - - 15 6. The wire size (or gauge) also depends on location, materials used, length of run, etc., so it must be determined by a qualified electrician. To select the different menu options, use the arrow buttons, which moves the brackets to the desired menu option. Warranty For warranty information visit: · Warranty Coverage Information · Warranty Registration · Warranty Verification Warranty coverage begins the day the ice machine is installed. Stainless finish with innovative clear-coat resists fingerprints and dirt. You will not hear refrigerant flow when the valves are opened. Ice quality is poor (soft or Poor incoming water quality. E08: TXV Fault Single or Dual Circuit Evaporators. It is recommended that this circuit be used to control the condenser fan(s) on the multicircuit condenser to assure it is on at the proper time. 6 to get the calculated drop. The foregoing warranty shall not apply to any ice machine installed and/or maintained inconsistent with the technical instructions provided by Manitowoc Ice.
Programs is selected, highlight Settings and press. · The condensing unit ships with a 50/50 mixture of nitrogen/helium. · If dirt still remains, call a service agent to clean the condenser. If one of them is selected and. Equipment Hazard Assessment to ensure During movement, cleaning or repair it is adequate protection during maintenance necessary to unplug both power cords. · Crush/Pinch Hazard. 75 lbs 1869 grams 2155 grams IBF0820C 5. Part Number 000014141 Rev 08 5/21 17 Installation Section 2 Electrical Requirements All electrical work, including wire routing and grounding, must conform to local, state and national electrical codes. Air cooled ice machine.
E20: Water System Fault. If the Manitowoc Indigo ice machine is stuck in off mode, then rebooting the Manitowoc will solve it. Female Pipe Thread Condenser Water Drain -- -- 1/2" Female Pipe Thread 1/2" (13 mm) minimum inside diameter Bin Drain -- -- 3/4" Female Pipe Thread 3/4" (19 mm) minimum inside diameter Large Capacity Bin Drain 1" Female Pipe Thread 1" (25 mm) minimum inside diameter Min. Ice machine stops, and can Service Fault feature stopping Refer to "Service Faults" on be restarted by pressing the ice machine. Freeze Cycle Water flows across the evaporator and the refrigeration system chills the evaporator. 5 inch drop per 5 foot (2. ADJUSTING SCREW 1/8" (3 mm) ICE BRIDGE THICKNESS PLACE 9/32" (7 mm) DRILL BIT BETWEEN PROBE AND EVAPORATOR TO SET INITIAL GAP Verify the ice thickness probe wire doesn't restrict probe movement.
Remove the water distribution tube(s) NOTE: Thumbscrews for the distribution tube are retained to prevent loss. Two or more people are required to lift or move this appliance to prevent tipping and/or injury. Lock the front casters after installation is complete. Apply refrigeration oil to the threads on the quick-disconnect couplers before connecting them to the condenser. 63 kg R410A Model/serial plate information overrides all data listed in this chart. In place and properly secured when operating this equipment. Unless you know what you are doing, avoid messing with settings in this sub-menu. NOTE: Touchscreen is to be activated with finger tips only.
keepcovidfree.net, 2024