The Nineth Problem: Computer Common Problems for Laser Engraving Machine. The fasten screw of the motor and belt pulley was loosed, fasten it. In the use of a laser engraving machine, you may be troubled with various problems, how to do troubleshooting? But wouldn't it be nicer to layout several at once and have the laser engrave them all? There is water: check whether the water inlet and outlet are connected reversely or the water pipe is broken. Laser Engraving Troubleshooting for Common Problems. We just need to adjust the laser ray path(this step will be trained when purchasing the laser engraving machine.
If shorting L and GND results in the light always being on, it indicates that there are no issues with the laser power supply or the laser tube. Self-test, send data does not light: Check the computer settings are correct. The left-right tensility of the Y axes were different, we should adjust the Y axes hexagonal screw to equilibrize the left-right tensility. If you follow these steps and still can't get your machine to work, please contact customer support for further assistance. Renew the cable and the stick will be to work. Gather information on the metal you're marking. Problem: You hit "Go" on the laser, "500 DPI" displays on the laser's screen, and it does not start your job. 19 Most Common Laser Engraver Problems and Solutions. Here is an example of patented shotblast resistant laser engraving: If you're marking for traceability, data matrix codes and QR codes are great options since barcode readers can read them more reliably than serial numbers. This may be because the laser beam is not set to the correct width or because the material you are engraving is not smooth enough. Therefore, the principle of selecting the focusing mirror is to use the focusing mirror with a shorter focal length as far as possible. A laser specialist will reply to your post with possible solutions in the next few days. If not, the water protection needs to be checked.
If both the motor and the driver are excluded, it is necessary to consider the motor wire and detect any short-circuits or open-circuits by using a multimeter to make detailed continuity measurements. The reversal of the origin's direction is usually due to a short circuit in the switch coil. Question 10: The parameter settings in the "Advanced Settings" of the laser engraving machine are invalid. Check whether the software parameter settings are correct; 4. There are 2 disadvantages to be aware of with this technique. Check whether the software parameter setting is normal, if it is abnormal, it needs to be restarted; 2. Solution: Cause: The "Piece Size" in the laser settings do not match the workspace size in the design software. Laser engraving on paper. The graphic size is too large or too small. B: if the indicator light is on, check whether the motor wire connection is good. Lastly, you can disable the water flow protection. Finally, if the engraver still won't turn on, it may be time to call a professional for help.
You might need to create some guides for laying out out your design or maybe you'll need a target to place an object in. When laser engraving metals, the metallic dust released in the air can affect the performance of the laser. If the error still persists, you may have an air bubble affecting the water flow sensor or the water flow sensor may need to be replaced. The Seventh Problem: Computer Can Not Output for Laser Engraver. Then measure one of your shapes/items. Check whether the belt or the synchronous wheel is slipping or tooth skipping. The laser tube is either cracked or damaged. Laser engraving problems and solutions center. Whether the serial port line has been used to connect the computer serial port and engraving machine, the connection is reliable. Increase vibration suppression in the software settings; c. Adjust servo parameters; - Check if the cylinder locks the exchange platform; - Ensure the laser head and related components are firmly fixed; - Inspect motor installation, ensure spacer installation is correct, and couplings are securely tightened; - Check if the slider screws are firmly tightened; - Check the engagement of X and Y axes, requiring 0. Engraving machine is according to the first positioning and then start the output.
Key points: power supply, fuse, control board card, driver, switching power supply, circuit). Your laser should have some options to determine the order in which lines are cut but one way for you to control that is to put different cuts on separate layers on to turn the print of each layer on and off in the order you want. Or draw horizontal and vertical center lines. Step 5: Tip #5: Lines - Raster Versus Vector. That knowledge will help to sharpen your skills with the laser engraver and cutter. Analysis of common problems of laser engraving machine. This might caused by the poor contact of the Memory belt. Warning: perform this step at your own risk.
Modify the data again). The exact thickness varies depending on the DPI settings used. Then place the scarp material in the laser and measure down and across from the laser's origin to the target area. No control card detected by online machine.
The water protection circuit is either broken or has poor connectivity. Laser engraving problems and solutions.fr. The direct reason for the lack of laser processing depth and processing speed is that the effective power density of laser processing is low. The third step is to inspect for any relative sliding between the loose rolling net and the feeding shaft and to check for any blockages. If you've measured everything correctly your cut out should be in the target area. The laser tube is connected incorrectly after the RF laser tube is replaced.
If this does not fix the issue, it is possible that the door sensor needs to be adjusted or replaced. The 24V transformer is malfunctioning. Then, adjust R103 and R28. Sometimes the switch is located on the back of the machine, so be sure to check there. The water temperature is higher than 30 ℃.
Option 1: The best solution is to move your design away from the edges of the laser in your design software. There is electric current: check whether the lens is broken and the light path is seriously shifted. Synchronous wheel screws are loose, the motor wire is broken, the motor is broken, the driver, voltage is abnormal, etc. Let's start one by one. Step 4: Tip #4: Overlapping Lines. The Fourteenth Problem: Sometimes Press The "Start Button", and The Data is Not Output.
For Baishan and YAKO stepping drives, if the DC power supply is normal and the motor line is disconnected, and the driver's indicator light is not on, it can be determined as a driver failure. The laser I use has the option to turn on a laser pointer that projects a red dot where the cutting/engraving laser will fire.
keepcovidfree.net, 2024