Minn Kota trollers are very popular for their durability and longevity. The armature converts electrical power to mechanical power. And the second way that control boards fail is when the boat is moving forward but not in reverse. The first connections we made in the controller was the black ground wire. If your Terrova has lost steering function, please read: Terrova/ST motors use drive housings that are specific to the voltage of the motor. In case you don't have a 12-volt battery, you can test it with the help of another boat. How to fix the switch on a Minn Kota trolling motor. If you don't have them at home, you can buy an armature kit. There a metal "box" area on the left side of the control board that got pretty warm when the TM was plugged in and I was testing it. I use the I-Pilot remote, not the foot pedal. How to test minn kota battery charger. Begin by trying out each of your forward speeds all by themselves. If the higher than normal amp draw of the drive housing is not corrected the steering circuit on the new/replacement control board will also fail. This website uses cookies to improve navigation and service.
You may have an electrical issue like a burnt-out armature or control switch, or you may have broken a prop drive pin. You may normally feel the trolling motor vibration, and that's okay. Second, your armature or brushes could have gone bad. Q: What is the difference between a drive pin and a shear pin? Bolted right in and plugged right without issues. How to Test the Trolling Motor. Unfortunately the board arrived here with a damaged part, but I think it was in the transport from the USA to Brazil, I did a repair with resin and I hope it works.
A drive pin is most often made from stainless steel and designed not to break even if the propeller hits something, so if it does break, you must have hit something hard. That's why you bought it in the first place. But how do you fix the noise? If you don't know, here is how to mount a trolling motor on a ski boat. After buying a new pedal, the momentary and continuous works, but steering does not. Buy replacement wires if some are damaged.
Thrust levels include 40, 45, 50, 54 and 55. Another friend brought the pieces to Brazil. The control board assembly is the brains of your Minn Kota trolling motor. You will want to keep these as close to the panel cutout dimensions to try to keep this as water proof as possible. Once attached, lower the motor into the water. The switch at the top of the board is used for selecting either momentary or continuous operation of the motor. If your trolling motor cuts in and out when you are trying to use it, it may be a sign of dirty brushes and/or a leak in the lower unit. It should be firmly attached and not able to move around. First issue ive had.
If it is greater than that draw then it likely is malfunctioning to the point it would have damaged the main control board. 00 Availability:: Usually Ships in 1 to 2 Business Days Product Code: 2774016 Qty: Description 12 Volt Terrova and Riptide ST Bow Mount The 12 volt control board assembly offered here is made to fit the 12 volt Terrova bow mount, or the 12 volt Riptide ST bow mount motors. Here's how to do a basic test of a trolling motor: - Make sure the trolling motor is properly secured to the boat. Before doing something like that, give this article a thorough read because we've rounded up all the possible reasons and fixes with our very own experts & mechanics. A: A drive pin is usually constructed with stainless steel and not designed to break, where a shear pin is made of bronze and designed to break when your propeller contacts something. This may be covered warranty as well, so be sure to ask. Works with all Terrova and Riptide ST non blue tooth 24 & 36 volt models. 5-volts for 24 or 36-volt drive housings) suspect that the drive housing has taken out the steering circuit on the main control board. For our build we also wanted to eliminate the exposed automotive trailer connectors. Step 4: Take out the old brushes and put in new ones.
The control switch has the speeds settings, the off position, and the forward and reverse controls. Thanks for the fast and efficient delivery. Secure it by cutting back on the screws and nut and then reconnecting all of your wires. But if the noise goes up a bit more than that, something is wrong. If you need more information on how this is accomplished, take a look at this post on our TechForum Polarity Reversal using a DPDT Switch - #2 by Ryan_2724. Something to cut the openings for the box like a Dremel.
The shear pin is a safety device designed to protect your motor. If your warranty is expired, or you are a do-it-yourself type of person, then go ahead and dismantle the lower unit. The resistance of this sensor ended up being about 850 ohms. Where: The control switch is located in the top of the trolling motor where the hand controller comes out.
keepcovidfree.net, 2024